It is specially designed to use in high wet environment of all kinds of electric power tunnel, with the characteristics of high protection, and low power consumption. A line can support 10 sets of telephones, and the standard of DTMF code sending exceeds 10 kilometers. With 1W speakers built-in, voice is clear and loud. The transmission distance could reach to 10 kilometers without additional power supply.
1. Product features
Automatically dial with one button
Call time limited
Send address code of this machine, and code sending time can be adjustable
High waterproof, dustproof performance, full aluminum phone cover, IP66 protection grade.Sprayed with imported reflective lacquer on the surface, bright color, 5-10 years not fading, completely conform to the standards of GB/T5237.2-2000.
2. Scope of application
It is applied to highway for emergency call, railway or subway for interval telephone call, and tunnels, electric tunnels for maintenance call.
3. Technical Parameters
Ambient temperature:-30 ~ +60 degreeRelative humidity:10%~95%
Atmospheric pressure: 86~106Kpa Circumstance noise:less than 60dB(A)
Sound level of ringing:over 70dB(A).
Standard frequency:low frequency group:697. 770. 852. 941Hz,
high frequency group:1209. 1336. 1477Hz, frequency deviation:-1.5% ~ +1.5%
If service line is a 3Km signal - level:
Standard frequency:low frequency group:-12dB~-6dB, high frequency group:-10dB~-4dB, level difference between low and high frequency of compound signal:0dB~3dB, the total distortion caused by intermodulation of harmonic wave is lower than the basic level by at least 20dB.
Call transmission index:(5KM)SLR<12,RLR<-1,STMR>10, output impedance is 600 Ohm
Parameters is kept in EEPROM, no losing with power-fail.
4. Function introduction:
Automatic dial-up function: press dial-up keys, 3 ~ 5 seconds for you will be designated to dial the number.
Call time limited: Automatically start seven minutes timing when connecting a telephone. When time is up, phone automatically hangs up in order to prevent lines occupied because of long conversation.
Send address code: Press the answering button when there is a phone call. Then send address code within 2s after answering. When call out, press the call button, send out this phone address code within 1-63s.Achieve the function of delay time through the internal dial-the-code switch.
Turn 1 to ON means delaying 1s. 2 mesns 2s.3 means 4s
......6 means 32s.
5. Telephone installation
Installation dimensions: 320*
Using four M8-6H*
6. Packing specification
Phone size: 320*230*120(mm)
Outside box size:439*277*191(mm)
VoIP SIP2.0 telephone DTMF dialing Audio Codes:G.711, G.722, G.729,G723,G.726
MTBF:100000hours MTTR: 2 hours Network:10/100 BaseTX Ethernet, RJ45
Free dial (maximum length of each number is 32 digits) connectors, Cat5e or better
Communication: Full duplex 2-way IP Protocols:IPv4, TCP, UDP, RTP, DHCP, SIP
Call Control Signaling:VOIP SIP Info(DTMF), RFC 1 x LAN Power over Ethernet(PoE,802.3af)
2833(DTMF) 1 x LAN(IEEE 802.1x), Network Access
Power:Power over Ethernet, IEEE802.3af, Class 0 Control(IEEE 802.1x),STP(IEEE 802.1d),
Local power, 12VDc,Idle 2W, Max 10W RSTP(IEEE 802.1d-2004)
Auxiliary Contacts: (option) Programming:Non-volatile flash memory
1 Aux Output, dry contact Programming and configuration through Web GUI
Dry contact Load parameter Management and Operation:DHCP and static IP,
Rated load:0.3 A at 125 VAC; 1 A at 30 VDC remote automatic software upgrade, centralized
Rated carry current:1A monitoring
Max.switching voltage:125 VAC,60VDC Echo cancellation code: ITU-T G.167/G.168
|Model number||Power Supply||Item Number|
|KNSP-04 -IP-Y_ADP||DC12V 1A +POE||SP0040102|